Skip to content

Sceptre Monitor No Signal (Guarenteed Fix)

Sceptre Monitor No Signal

Sceptre inc was founded in 1984 and has since been in the business of building and innovating high-tech TVs and monitors.

Their highly affordable 4K UHD monitor with Built-in Speakers has recently created a lot of buzz in the market. But unlike giant-tech manufacturers like Samsung and Acer, Sceptre monitors are more prone to display issues.

One of them, the “Sceptre monitor no signal” issue, has been a highlight. Here are the reasons, causes, and solutions to this issue,

ProblemCauseSolution
A loose video cable, i.e., HDMI, VGA, thunderbolt, etc.Improper insertion, loose screwsDisconnect and reconnect the video cable at both ends
Damaged display cables or portsOver-twisting, Frequent Insertion RemovalReplace the video cable with a new one/repair the damaged port/use an alternate port
Problem with the graphic card, including its port or chipsetShort Circuit/Physical DamageUse Builtin Video port/Repair graphic card/Remove, clean, and reconnect graphic card
Loose or Dusty RAMDusty EnvironmentRemove RAMs and clean with Isopropyl alcohol and nylon brush
Selecting the wrong input and output sourceNonSync Input Output source selectionselect the proper interface to set up the monitor connection
Corrupted BIOS SettingVirus/SoftwareRest BIOS setting to default
Sceptre Monitor No Signal

First, check the video cable connections to fix your Sceptre monitor’s “no signal found” issue by disconnecting and reconnecting the video cable. If it does not work, look for damaged video ports, graphic cards, or RAMs and repair or clean them. Lastly, reset the bios if nothing is working for you.

Now that I have summarised the issues and their solutions, let’s discuss them in detail,

Fix 1: Tightening a loose Display Cable

A loose display cable connection mostly causes no signal issue on Sceptre monitors. Therefore, ensure that all the cables connected to your Monitor and PC are firmly attached or screwed tightly.

Moreover, If you use an HDMI interface, set the audio signal to Pulse-code modulation (PCM) instead of Bitstream. If you are using a TV antenna as your source, make sure your signal is strong by using a booster.

Also, connect the display cable to the designated port. If you have a graphics card, connect the cable to the card port.

It is important to remove the graphic card before using a built-in video port on a PC, or the port will not receive a signal.

Fix 2: Replacing Display cable/Repairing Port or Using alternate input port

If you are sure enough that your video cables are connected properly. But still, your Sceptre monitor is showing the message “no input signal found,” it’s time to visually check all the cables for any physical damages like overtwisting, cracking, bent pins, etc. If you find any fault, replace the cable right away.

If your cable is normal, then the display port might be damaged. Due to repeated removal and insertion, the male ports damage the female port, and the port becomes loose over time.

This fails to create a secure connection and hence needs repair. An expert can only change the port, so do not try it yourself because you might damage the PC board.

Alternatively, you can use other video ports like HDMI instead of VGA and vice versa. However, do not forget to change the settings on the monitor through the OSD menu.

Fix 3: Remove and clean or Repair the graphic card

The graphic card is the motherboard and processor of visual input. It will fail to work if your graphic card isn’t connected to the main motherboard correctly or loosely fits.

Carefully removing and reinserting the card firmly might solve the no-display signal problem on your Acer monitor.

Moreover, a dusty and un-clean graphic card also fails to work properly. So if you haven’t cleaned your PC in a while, this might be why you are not getting video signals. Below is a video that will help you with cleaning it.

If your graphic card smells burnt, it might not be good news. The fans on the graphic card suck in air for cooling purposes, and sometimes due to extreme moisture or humidity, water vapor condenses over the board, which might short-circuit and burn critical ICs.

Often these ICs are so small that they are irreparable, and you might need to buy a new one. However, an expert technician might get you out of hot water.

Fix 4: Selecting the proper interface

Most monitors, including Sceptre, provide multiple display ports like VGA, HDMI, DisplayPort, or other interfaces.

Therefore, you’ll have to match the correct input and output source; e.g., if you are using a VGA connection but the source is set to HDMI, your monitor will not detect the VGA.

Similarly, selecting different HDMI ports might as well trigger no input signal. Here is how to choose the proper input source on your Sceptre monitor:

  1. Press the OSD button on your monitor to launch the On-Screen Display (OSD) menu. Depending on the model, the button might be located on the front, back, or bottom.
  2. Next, go to Settings and select the Video Input control section using the guide buttons.
  3. Select the proper interface matching input and output source.

Fix 5: Resetting the BIOS

A virus, software, or new windows installation might get your BIOS/UEFI setting to set off. This can trigger the same no-signal issue on your Sceptre monitor.

Therefore you must reset the BIOS/UEFI to default settings. For this, follow these steps,

  1. Restart your computer; it will ask you to press a button to enter BIOS setting. Depending on the PC manufacturer, the key might be F10, F2, F12, or F1.
  2. Once you enter a blue or black BIOS settings menu in the right-most corner, there is an option “EXIT” once you press this, it opens a window that shows the Restore to Defaults option.
  3. Once you press this, it will ask you again. Press “yes,” and your BIOS setting will change to factory settings.
  4. Once the BIOS is reset, your computer will restart automatically, and the HP monitor will start working properly.

Fix 6: Cleaning the RAM

If your PC RAM is dodgy or dusty, you’ll get issues with the display output. GPU Card comes with its VRAM, but bad system RAM will still lead to display issues.

Therefore cleaning the RAM should be the priority for fixing “No signal-found issues” on your Sceptre Monitor. Cleaning the RAM is easy; all you need to do is,

  1. Unplug the power
  2. Unscrew the PC covers and remove them
  3. Locate the RAM slots, usually next to the fan on the processor.
  4. Unplug the RAM by pressing the hinges and removing them.
  5. First, clean the dust with air or a piece of cloth, and then carefully spray recommended Isopropyl alcohol (For Electronics).
  6. Next, brush the gold contacts with a toothbrush carefully.
  7. Wait for 10 minutes so that the alcohol completely vaporizes.
  8. Plug in the RAMs in designated places carefully. Slot marks will help you push RAM in place.

Do not Push hard when inserting RAM (they usually slide in easily). A forceful insertion will damage the slot, the RAM, or the motherboard.

If you are still experiencing issues, please contact the support team.

Leave a Reply

Your email address will not be published. Required fields are marked *